Boarding Up Windows And Doors Tools To Streamline Your Everyday Lifethe Only Boarding Up Windows And Doors Trick That Should Be Used By Everyone Know > 자유게시판

Boarding Up Windows and Doors Before a Storm Hits

When a storm is approaching the windows and doors provides measurable protection from damage. To do this, you need to have a few things on your desk.

First, take measurements of the width and height of the window including the framing (not the surrounding trim or masonry). Keep these measurements in mind so you don't forget.

Preparation

It is recommended to board up your windows and doors before a storm or natural disaster. This will prevent property damage and minimize loss of life. 24 hour boarding up service up windows requires a lot of preparation, like purchasing and measuring plywood boards, and determining the exact dimensions of each window that needs to be covered. It also takes time to cut the boards and put them up them correctly. Fortunately it is possible to make the process simplified by starting the preparations immediately you learn of a possible storm forming in your area. By doing so, you can stay clear of a stressful last minute rush and make the process easier for yourself and your employees.

Begin by listening to forecasters of the weather and following the guidelines set by your local government. If you start earlier in the process, you'll be able to gather the materials and keep them in storage without feeling rushed by a storm that is about to hit. You may require a substantial amount of plywood to cover your windows, dependent on the severity and imminence of the storm. To ensure you get the right size, you can make use of a tape measure determine the width and height of each window opening. Make sure to consider the framing or trim that surrounds each window, as well as any extended sills when applicable.

Divide the total width and the height of your window boarding up near me by 2 to determine the number of plywood sheets that you'll need. If your window is wide of 16 inches, then the thickness of each sheet is 8 inches. If you have wood exterior, drill pilot holes in the plywood sheet that align with the window frame beneath to reduce splitting when you screw in the screws.

To make sure that the window's opening is larger than what one sheet of plywood can handle cut two sheets that are each half the size of the desired window and place them side-by-side on the wall. Cut a piece of 2 by 4 in (5.1 10.2 cm) 10.2 cm) of lumber to the length of the connecting edge between the sheets of plywood, and place it on top of the seam. Then you can drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them.

Materials

To ensure safety and security For your safety and security, only use materials that are strong and won't be damaged or break in high winds. Plywood is the most common material to board up windows. It is simple to work with, cheap and easily available. Select plywood that is exterior grade (CDX) because it is more durable and have less knots and warps. Storm shutters, also known as hurricane shutters, are a more durable option. They can be put in over existing windows and offer better protection against glass breakage and weather conditions that can be severe.

Once you have identified the location of the window openings, you can determine the height and width to determine the amount of plywood you'll require. Then you can use a power drill to create pilot holes into the plywood sheets at two-inch intervals around each window. Mark the studs on the wall prior to attaching the plywood to ensure the boards are fastened securely. If you have wood siding in your home, search for nailheads in order to determine stud position. You could also use your drill to locate the studs' locations. The screws should be driven into the framing, not the trim or sheathing. A plywood panel attached to these materials may be a danger to safety during strong winds.

If your window is too big for one sheet of plywood, you could cut two pieces of plywood each half the size and join them using two by four inches of lumber. Label each piece of plywood so that you know which window it will be covering.

To secure the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to get through both the sheathing and the studs. Aim to insert the screws into the studs in a way that they are half the depth of the thickness of the plywood, however, be cautious not to go too far and cause damage to the structure of your house.

In addition to protecting your windows, it is also advisable to put up a "No Trespassing" sign on the property, and consider installing polycarbonate security glazing like DefenseLite over your windows. These transparent shields bond over existing glazing to safeguard your windows and doors and are virtually indestructible, preventing criminals from gaining entry.

Installation

If you live or plan to move to a region susceptible to hurricanes and are concerned about the storm it is recommended to board up your doors and windows. This task can be completed quickly and efficiently, however only if the plywood panels are measured, cut, and labeled before the storm arrives.

You'll also require a few other tools, including drills (or a hammer and nails if you don't have a power drill) and tape, a saw an apron, gloves and safety glasses. It is a good idea to coat the plywood with sealant and make it waterproof.

Start by measuring the height and width of each window opening, then cutting your plywood sheets to ensure they can fit inside the frames, with an overlap of 4 inches on all sides. It is best to do this on-site, as it gives you more control over the precise dimensions of the plywood.

Use a circular saw or track saw to cut the boards to the proper size be aware that you'll need to sand them down once they're put in. Once the boards are set put the 3 inch stainless hanger screws made of steel into the framing posts around each window. Use washers to secure each bolt and wing nuts. Make sure that each screw is able to penetrate the studs at least two inches to ensure the board is strong enough to withstand strong winds.

If you're building using concrete blocks, you can attach the plywood with pan head screws that are galvanized and that are driven into the overlapping edges of the panels to bricks or cinder blocks. It is also necessary to drill pilot holes into the masonry before screwing corrosion-resistant screws into the holes. It's a job that can take up to three hours per window, so it's essential to begin the process when you learn that a hurricane watch has been issued. This will allow you plenty of time to finish the project before the storm arrives.

Maintenance

If you're a homeowner, or business owner, it is essential to have the right materials to board up doors and windows ahead of an extreme storm. This will help you to avoid expensive repairs and protect your home from further damage that could be caused by wind, rain flying objects, and other factors.

The right materials will make boarding up company simpler and faster. It is essential to precisely measure the windows. This will ensure the OSB or plywood fits snugly, and that it won't come off easily. If you are using plywood, make sure you use exterior grade sheets and consider adding an additional protective finish.

After you have the plywood or OSB taken measurements, mark the locations where the screws will go into the board. Make use of a drill to drill holes at intervals of 12 inches into the plywood. Then, you can use hanger bolts to anchor the boards in a emergency situation. When the storm has passed and the local authorities have given you the all-clear to go ahead, remove the bolts, but save them in case of a need in the future.

Then, you can install the plywood panels over the windows. This is a two-person job So, be prepared before you start. If you're using plywood then sand the edges to make them smooth so that they don't scratch paint or cut. Then make use of corrosion-resistant screws join the plywood with the pilot holes. If your home is clad with vinyl shingles it is recommended to nail the plywood to the shingles rather than the wood framing beneath.

Apart from keeping out the elements of weather and water elements, a boarding up windows service up window is also a good way to prevent burglary. Burglars will target a building with a damaged window or one that is not locked. They are also more likely to break into a store with a boarded-up window than one with. This is something that retail business owners should consider very seriously.